SciCan Statim 2000 Manual do Operador

CALL (800) 221-9723 or (818) 882-8611 • FAX (818) 882-7028• E-MAIL [email protected] • WEBSITE www.rpiparts.comReplacement Parts Indust

16 17OILEVELSTARTSTOPREMOVE THIS LABELSERIES STELIZERFOR USE WITH 5000LEAVE THIS LABEL ONSERIES STERILIZERFOR USE WITH 2000DAILY OPERATIONIf the quick

18 19Cassette Seal SCS001Compressor Filter SCF002Biological Filter SCF032PART RPI PART # STERILIZER PM TIPRefer to the “Installation and Monthly Maint

20 21Cassette Seal SCS029Air Compressor Filter SCF031Biological Filter SCF032PART RPI PART # STERILIZER PM TIPRefer to the “Installation and Monthly M

22 23STEP #1 - The cassette must be opened and cooled before removing the cassette seal. See Figure A.STEP #2 - Start with any of the (4) corners and

24 255.0 – SERVICE TIPS1. CASSETTE DIAGNOSTICSIf water is leaking at the drain from the cassette bay (un-derside of autoclave), then do the following:

6.0 – LCD ERROR CODES (Note: Error Codes that are not currently used by Sci-Can are listed as "Not Currently In Use" or not listedin this bo

28 296.0 – LCD ERROR CODES (continued)STAGE #3 – PRESSURIZINGThe pressure increases as the cassette temperature rises to the factory set temperatures

30 316.0 – LCD ERROR CODES (continued)STAGE #4 – STERILIZATION(continued)LCD MESSAGE CHECK CASSETTE #7 (CYCLE FAULT #7)The steam generator/boiler or

32 336.0 – LCD ERROR CODES (continued)STAGE #5 – VENTING(continued)LCD MESSAGE CYCLE FAULT #16Steam generator/boiler temperature "ran away"

34 357.0 – LCD MESSAGESAPPLIES TO ANY STAGELCD MESSAGEGARBLED OR NO READ-OUT ON THE LCDTHINGS TO CHECK• Make sure that the cable from the LCD board (R

1FIGURE 1 – STATIM 2000 & 5000 KEYPAD SYMBOLS CHARTRubber Model 2000 Unwrapped Wrapped & Plastics Air Dry Start StopRubber Heavy DutyModel 500

36 378.0 – TROUBLESHOOTING TIPSCONDITION:WATER QUALITY SENSOR TROUBLESHOOTINGApplies to the STATIM models with water quality sensoronly.THINGS TO CHEC

FIGURE 9.2 - CLEANING THE STEAM GENERATOR/BOILERFIGURE 9.1 - STEAM GENERATOR/BOILER38 399.0 – REFERENCE BLOCKS • To check the thermal fuse continuity

FIGURE 9.3 - STEAM GENERATOR/BOILER CALIBRATION PROCEDUREFIGURE 9.4 - SOLENOID VALVE40 419.0 – REFERENCE BLOCKS (continued)Applies to STATIM 2000 and

FIGURE 9.6 - PUMPFIGURE 9.5 - CASSETTE42 439.0 – REFERENCE BLOCKS (continued)CASSETTE DIAGNOSTICS:If water is leaking at the drain from the cassette

FIGURE 9.7 - AIR COMPRESSORThe OEM recommends replacing the compressor filters every 6 months or every 500 cycles (whichever comes first).Flow44 459.0

46 472143658710 912 1114 13151719P1ThermocoupleMicroswitchSolenoidValveAir CompressorSteam Generator/BoilerInvensysWaterQualitySensorThermocoupleHeate

48 49FIGURE 9.9 - PLUMBING DIAGRAM9.0 – REFERENCE BLOCKS (continued)Female Quick ConnectFitting (Drain Line)ReservoirPumpIn-LineWater FilterSteam Gen

50 51ADC058 No OEM Part # Available CORD CLIP - 10/PKG • •CAF011 No OEM Part # Available RUBBER FOOT - 4/PKG • •RPB365 53-100518A 90º LIQUID TIGHT STR

52 53NOTES11.0 - RPI TOOLS & ACCESSORIES LIST(FOR PARTS TO FIT STATIM 2000 & 5000)RPA369 No OEM Part # Available THREADLOCKER 545 • •RPB792 No

Parts mentioned in this booklet are manufactured by Replacement Parts Industries, Inc. to fit SciCan STATIM® Cassette Autoclave Models 2000 and 5000.

23THISUPSIDEUPSIDETHISTHISUPSTOPSTARTLEVEL290FILL LINEMINIMUMGOLRKNNINCUOI2.1 – Extension Test CableRPI Part #SCT026(see page 4)2.2 – Start SwitchRPI

4 52.1 - EXTENSION TEST CABLE(RPI PART #SCT026)When testing, troubleshooting or repairing the STATIM au-toclave, install the RPI Extension Test Cable.

6 72.3 - PUMP TESTER BOTTLE(RPI PART #SCK024)The RPI bottle has a “swivel fitting” on the lid that allowsyou to control the position and balance of th

8 92.4 - SPANNER NUT(RPI PART #RPT364)When removing the solenoid flute/bonnet, it is suggestedby the OEM to use a pair of pliers on the welded area of

10 112.6 - CASSETTE SEAL REMOVALTOOL (RPI PART #RPT372)The Cassette Seal Removal Tool was designed to help remove the cassette seal for either mainten

12 13FIGURE 2.10BTIP - If realigning existingprobe bracket, loosen (DO NOTREMOVE) 4 mounting screwsand compression fitting con-nections to allow repos

TDS114 152.11 – WATER QUALITY TESTER(RPI PART #RPT820)The Water Quality Tester (RPI Part #RPT820) is a meter de-signed to measure water quality. This